Sensor
| Sensor | Sony IMX546 Gen4 |
|---|---|
| Mono/Color | Color |
| Sensor type | 2/3″ CMOS |
| Shutter type | Global shutter |
| Resolution | 2848 × 2832 px |
| Pixel size | 2.74 × 2.74 µm |
| Exposure time | 0.001 … 60000 ms |
Image Formats & Frame Rate
| Image formats, interface frame rate max. | Full Frame, 2848 × 2832 px, max. 15 fps Binning 2×2, 1424 × 1416 px, max. 16 fps Binning 2×1, 1424 × 2832 px, max. 16 fps Binning 1×2, 2848 × 1416 px, max. 16 fps |
|---|---|
| Image formats, aquisition frame rate max. (Burst Mode) | Full Frame, 2848 × 2832 px, max. 16 fps |
| Pixel formats | BayerRG8 BayerRG10 BayerRG12 BayerRG12 Packed Mono8 Mono10 Mono12 Mono12 Packed RGB8 BGR8 |
Functions & Controls
| Analog controls | Gain (0 … 48 dB) Offset (0 … 255 LSB 12 Bit) |
|---|---|
| Color models | Mono Raw Bayer RGB BGR |
| Basic Functions | Exposure Gain / Color Gain Trigger / Exposure Active (Flash) Binning 2x2 Partial Scan Offset Free Running Mode (Live Image) |
| Auto Functions | Exposure Auto Gain Auto White Balance Auto Color Transformation Auto |
| Image Pre-processing | Image Flipping (X/Y) Color Processing (RGB, BGR, Mono) Color Enhancement (with optimized ColorTransformationMatrix) LUT / Gamma |
| Acquisition / Interface | Burst Mode Adjustable Framerate Device Link Throughput Limit Internal Image Buffer |
| Additional Functions | User Set Integrated temperature sensor Readable additional information (e.g. sensor information) |
| Calibration data | Integrated color correction matrix (3000 K, 5000 K, 6500 K, 9500 K, and user defined) Camera calibration data (user defined storage for intrinsic / extrinsic camera parameters, and geometry distortion values) Customer data storage (128 bytes user defined) |
| Internal image buffer | 185 MB|8 image (Trigger Mode)|1 image (Free Running Mode) |
Synchronization & I/O
| Synchronization | free running trigger |
|---|---|
| Trigger sources | Hardware Software ActionCommand |
| Trigger delay | 0 … 2 sec, tracking and buffering of up to 256 trigger signals |
| Process Synchronization | Events Timer Trigger Delay Debouncer Counter Sequencer Trigger via Action CMD (GigE) Additional Output Modes (e.g. Trigger Ready) PWM (PWM Duration / PWM Duty Cycle) 4 power outputs with up to 120 W (max. 48 V / 2.5 A) Selectable Output format (e.g. Tri State, Push Pull) Chunk data inside transferred image Encoder support via Counter End trigger source |
| Lines | 4 input lines 4 power output lines with pulse width modulation (PWM) (max. 48 V / max. 2,5 A) |
| Output line sources | Off Line 0-3 Exposure Active Timer1Active Readout Active UserOutput 1-4 TriggerReady |
Interface & Connectivity
| Data interface | Gigabit Ethernet, Transfer rate 1000 Mbits/sec, Fast Ethernet, Transfer rate 100 Mbits/sec, Connector: M12 / 8 pol x-coded, screwable type |
|---|---|
| Process interface | M12 / 12 pins a-coded (SACC-CI-M12MS-12CON-L180) |
| Power supply | via M12/12 pins a-coded or Power over Ethernet (PoE) |
Mechanical
| Lens mount | C-mount |
|---|---|
| Width | 40 mm |
| Height | 40 mm |
| Depth | 50.8 mm |
| Weight | ≤ 137 g |
| Material | aluminum, hard-anodized |
| Protection class | IP 40 IP 54 (with mounted tube and cable) IP 65 (with mounted tube and cable) IP 67 (with mounted tube and cable) IP 69K (with stainless steel housing accessory) |
Electrical & Environment
| Power consumption | Approx. 2.9 W 12 VDC and 15 fps Approx. 3.5 W 48 VDC (PoE) and 15 fps |
|---|---|
| Flash memory size | 128 kB |
| Operating temperature | 0 … +65 ° T = measurement point |
| Humidity | 10 … 90 % (non-condensing) |
Compliance
| Conformity | CE RoHS |
|---|
Other
| Dark noise | 2.38 e- |
|---|---|
| Saturation capacity | 9266 e- |
| Dynamic range | 69.7 dB |
| Signal-to-noise ratio | 39.7 dB |
| Quantum efficiency | 44.6 % 465 nm|51.5 % 535 nm|39.8 % 630 nm |
| Color processing | Integrated color processor for high quality color calculation |
| Voltage supply range +Vs | 12 … 24 V DC (external power supply)|36 … 57 V DC (Power over Ethernet) |
